BED Online Magazine - The Bed Blog - We are crazy about beds. » diy

DIY: Christmas Ornaments

TanYA — Sat, 21 Nov 2009 03:08:23 +0000

This christmas save money on decorations and use your old toys to make Christmas ornaments! You don’t need to be picky and can choose anything that looks cute and has a special meaning to your kids.

Read the rest of the instructions here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Christmas Ornaments

DIY: Scrap Table

TanYA — Fri, 20 Nov 2009 17:57:26 +0000

We always support recycling here at Bedzine so don’t go throwing out your wood scraps yet. Instead make a Scrap Table and all you would need is salvaged wood, : five threaded rods, about four bucks each; nuts, washers, and screws; a gallon or so of wood glue; sandpaper; and polyurethane.

Read the rest of the instructions here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Scrap Table

DIY: Bean Bag Warmers

TanYA — Tue, 17 Nov 2009 21:15:14 +0000

Face the winter chill by making personilized bean bag warmers which are are a great alternative to heating pads.They can be used over and over, heat up quickly in the microwave, and there’s no wires or plugs to fuss with.

You will need – fabric, sewing supplies, pinto beans or rice

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Bean Bag Warmers

DIY: Rustic Outdoor Table

TanYA — Tue, 10 Nov 2009 19:05:23 +0000

Enjoy outdoor lunches with a lot of panache by eating on a rustic outdoor table. You don’t need to purchase something like this as you can make it at your own backyard.

The materials required for a table were conveniently the same as the materials available from the broken gates, namely

4×4 posts approx 6ft long (4)
4×2 rails approx 3ft (2)
Palings (enough to cover a 6ft x 3ft surface)
Hinges (4)

Read the rest of the instructions here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Rustic Outdoor Table

DIY: Floating Candles

TanYA — Tue, 10 Nov 2009 17:03:41 +0000

Halloween may be long gone but you can still have spooky fun. Float some candles in the air and create the perfect eerie atmosphere.

“The key here is to find the center of gravity of your candle so that you know where you can hang it from. Here I’m holding the candle between two fingers to see if it settles correctly You can also try balancing it on a finger. Now make a mark just slightly above this point. I’m doing this test on a new candle, but I’d recommend letting the candle burn until the flame “settles” inside the candle before doing this. The candle will be burning a little slower here and give you a bit more burn time in the end”.

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Floating Candles

Periodic Picnic Table

TanYA — Wed, 04 Nov 2009 08:27:03 +0000

For someone who always flunked chemistry, it’s ironic that I fancy the Periodic Picnic Table. So next time you are waiting for some sumptuous food, you can kill time by brushing up your elements. The table can be used both indoors and outdoors.

Via Gear Fuse

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

Periodic Picnic Table

Kitchen DIY – How to Add a Colorful Backsplash to Your Kitchen Counter!

Max — Thu, 29 Oct 2009 17:08:13 +0000

Here’s a quick one for those of you who have boring white or grey colored kitchen, try adding some color with by adding a backsplash color such as yellow (shown here) to your kitchen.

via apartmenttherapy

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

Kitchen DIY – How to Add a Colorful Backsplash to Your Kitchen Counter!

Chair Design DIY – How to Make a K’nex Chair!

Max — Tue, 27 Oct 2009 02:24:33 +0000

I’ve seen some great Lego chairs, all made from lego pieces but this is the first K’nex chair made from all K’nex pieces. You can try this yourself by following this DIY guide that shows you how to make a K’nex chair. Brilliant!

furniture made out of k’nex has always fascinated me, that’s what motivated me to make this chair out of k’nex.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

Chair Design DIY – How to Make a K’nex Chair!

DIY: USB Flash Drive Rubiks Cube

TanYA — Mon, 26 Oct 2009 17:09:42 +0000

All you techies out there who love tinkering with gadgets should read this DIY. Now you can make a cool modified USB Flash Drive Rubiks Cube and exercise your brain wherever, whenever. See the video for all the details.

material:

a very small usb flash drive (e.g. EagleTec USB Nano Flash Drive or Delock USB Nano Memory stick)
(e.g. from http://usb.brando.com/eagletec-usb-nano-flash-drive_p00892c041d15.html)
a corner piece of a Rubik Cube
an edge piece of a Rubik Cube
self-hardening synthetic clay (I used “Apoxie® Sculpt”)
a lip balm stick (I used a ”Labello“)
a small screw (I got mine out of an old dvd player, it’s about ~0.6 mm high)
a washer Ø 1.2 cm
Tiles or stickers (e.g. from cubesmith.com)

tools:

a Dremel (Felt Polishing Wheel, different grinding stones, precision drills) (you don’t have to get a very expensive one, I got mine pretty cheap on ebay)
a small slotted screwdriver (to apply the clay)
sandpaper (400, 800, 1000)
a black permanent marker
a small saw (I used one for metal)
a box cutter

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: USB Flash Drive Rubiks Cube

BED Accessory DIY – How to Make Super Mario Bros. Themed Baskets!

Max — Sun, 25 Oct 2009 20:54:07 +0000

Is your dining table looking empty? How about adding some flare to it by making one of these Super Mario Brothers themed baskets? Not only will your kids love this, you can use it to hide candy and other sweets as reward for your kids doing their homework. – link

Halloween last year I completely forgot about the baskets until the night we went out. I ended up just using an orange bucket we had laying around. This year I wanted something that matched the costumes that we were making. For Yoshi I decided to do an egg for his basket, and for Baby Mario a Super Mushroom.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

BED Accessory DIY – How to Make Super Mario Bros. Themed Baskets!

DIY: Pumpcans (Pop Can Jack-O-Lanterns)

TanYA — Wed, 21 Oct 2009 19:32:59 +0000

With Halloween coming up, make sure you are in the loop when it comes to all the funky and spooky decorations. Hence try making the Pumpcans (Pop Can Jack-O-Lanterns) at home and wow the kids with your super cool work of art.

To make pumpcans, you will need…

* Empty pop cans (1 per pumpcan)
* Exacto knife
* Needle nose pliers
* Tea candles (1 for each pumpcan)
* Matches or other firestarter

Optionally, you may also want…

* Dremel tool
* Scissors
* Stencil or other pattern
* Thin sharpie marker
* Spray paint
* Sandpaper

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Pumpcans (Pop Can Jack-O-Lanterns)

DIY: iPhone Alarm Stand

TanYA — Mon, 19 Oct 2009 16:04:51 +0000

Make an iPhone Alarm Stand that has been inspired from a Kensington stand. The idea is to have the iPhone not lying down when charging or using as an alarm.

Things You Need:

For this you will need the / a charging cable like the one that came with the iPhone. Some graph paper pencil accurate way of cutting acrylic, saw Glue stick scissors sandpaper Some scrap acrylic or wood or anything similar.

Read the rest of the post at Instructables.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: iPhone Alarm Stand

DIY: Halloween Lamps

TanYA — Sun, 18 Oct 2009 19:45:04 +0000

Get into the Halloween spirit and make some funky cool Halloween lamps at home. The key to the project is that the lights are low voltage, low amperage, do not get hot and are easy to handle.

Here is what you would need:
“Most of the tools and supplies are shown in this step. Orange paper, black cardstock, acrylic paints, cutting tools, straight edge, etc. And of course the lights. These are regular Christmas tree lights, found in any dept. or craft store.”

To read the rest of the post go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Halloween Lamps

DIY: Tooth Fairy Pillow

TanYA — Tue, 13 Oct 2009 18:57:08 +0000

We simply love the Tooth Fairy Pillow as it pays homage to a myth we all have grown up with. You can easily made the pillow at home and this makes a great gift for (or with) a loose-toothed child.

Supplies and Cutting Fabric
You will need: 2 – 8″ x 8″ square pieces of fabric (Note: it’s really cute if you use two contrasting patterns) 1 – 4″ x 4″ piece of colored felt (to use as pocket) 1 – small piece of white felt cut in the shape of a tooth (approximately 3″ tall by 2.5″ wide) 10-12″ piece of ribbon to use as hanger for pillow Scissors Needle and embroidery floss (white, brown, blue, or colors of your choice) Pinking shears are optional but add a nice finish to the edge of the pocket. Sewing machine or needle and thread to hand sew. Step One: Cut out your fabric. So you have 2 (even) 8″ squares. I mark mine with a marker and a ruler but you might want to use chalk or a pencil if you’re working with light colors.

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Tooth Fairy Pillow

DIY: Super Cool Chair Tent

TanYA — Mon, 12 Oct 2009 21:40:55 +0000

Make the “Super Cool Chair Tent” at home and watch your kids go gaga over it. It is constructed entirely out of fabric so it can be folded and stored away quite easily. (If you want to recycle — an old queen size sheet set will accommodate the entire project.)

You will need:

* 8 yards of woven fabric or one set of queen sheets (pillow cases included)
* Sewing machine
* Thread to match
* Scissors
* Pins
* Tape measure
* Various prints of scrap fabric for decoration
* (Not necessary but super handy: a rotary cutter, ruler and cutting mat)

If you choose to decorate with appliques you will also need:

* Fusable Web (Wonder-Under)
* Paper or lightweight cardboard for making appliqué patterns
* Iron
* Various prints and sizes of fabric for decoration

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Super Cool Chair Tent

DIY: Build a Polished Concrete Desk

TanYA — Wed, 30 Sep 2009 21:30:52 +0000

Build a Polished Concrete Desk and save some money in the process. Just follow the instructions in the DIY here.

“Plan and layout the desk. Take measurements of the location you plan to place it. Nothing is worse than building something you wont be able to use. Make sure the concrete is broken up into manageable pieces both to prevent fractures, and to make sure that it is humanly possible to carry it to its final location! Also consider styling and other design elements. I decided to build a relatively minimal and modern corner desk.”

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Build a Polished Concrete Desk

KipKay Alarm Clock

TanYA — Sat, 26 Sep 2009 21:36:09 +0000

Don’t be fooled by this innocuous looking contraception. As the KipKay may just be the loudest alarm clock on the block or the world ! Don’t believe us? Then check out the video below for how ear splitting it really is!

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

KipKay Alarm Clock

Laptop Stand for Bed

TanYA — Sat, 26 Sep 2009 19:33:00 +0000

Who doesn’t like using the laptop in the bed? More importantly who doesn’t end up with a back pain when using the laptop in the bed? If you like me also refuse to give up this bad habit, then this DIY will interest you. Learn how to make an ergonomically designed laptop stand for bed and the best part? It will only take you around 30 minutes!

Materials Needed:
-wood strip, .75 in x 1.75 in x 6 ft. Just about anything of the right size will do.
-hard board, MDF board, etc – I used MDF the first time due to the clean white melamine coating, but the plain hardboard looked better and seemed more durable.
-two knobs attached to screws/bolts
-two big washers
-two socket anchors
-2 very short wood screws (for the lip)
-4 medium wood screws (for the legs)
-4 small nails
-4 plastic checker pieces (optional)

Tools:
-circular saw (could use a hand saw, but it’d be messy)
-power drill
-(Optional) dremel w/ sander bit

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

Laptop Stand for Bed

Tea Light Lantern Fluorescent Lamp

TanYA — Thu, 24 Sep 2009 21:32:13 +0000

If you love the idea of tea light lanterns but hate the idea of open flames and dripping wax, then this DIY is just for you. Learn how to convert a tea light lantern into a funky little compact fluorescent lamp! Things you need:

Tools:
Hand Drill
1/8″ (or similar) drill bit
Sheet Metal Step Bit (or a 7/16″ drill bit)

Materials:
Tea Light Lantern (I am using a “Roterra” from IKEA)
C7 Compact Fluorescent bulb (I am using an E12 “Sparsam” from IKEA)
Chandelier Bulb Socket
Lamp Hardware Kit
Rotary Thumb Switch
Electrical Cord

Read the full post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

Tea Light Lantern Fluorescent Lamp

DIY: Work Desk

TanYA — Tue, 22 Sep 2009 23:40:52 +0000

Make a fully functional work desk by using old wooden boxes and crates. The best part? You don’t need to be a bonafied carpenter to accomplish this feat of work.

An excerpt:

“I wanted to use crates found at garage sales and thrift stores for the drawers, have a tidy cable and cord system, shelving integrated, not conceal too much of the wall, and to fit the space that I had evenly. I also wanted to spend as little money as possible on it and use salvaged materials.”

Read the full instructions here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Work Desk

DIY: Pac Man Pouf

TanYA — Tue, 22 Sep 2009 19:36:12 +0000

Before the Wii and the PS3, there was Pac Man and those from my generation will vouch how addictive it was. Hence I love the Pacman pouf which can be made at home by following the directions here.

Material list:
- 15 mm MDF, depending on the size, you will need at least the C-shape to be created from one piece.
- 9 mm multiplex (plywood)
- 32mm*40mm timber (count number needed * height for total length needed)
- larger ones (for example 40mm*40mm) for the corners and block
- upholstery. I used sky to get that leather-look, but it is not so flexible. Mine had already some sliding-stuff on the inside, so it can slide over the foam. If you get other stuff, inform if you need additional stuff.
- cardboard strips. I had special ones, but you can cut some yourself
- staples…. lots!

Equipment needed
- workmate / bench
- Jigsaw
- drill
- drill-bits
- countersink
- screws (about 30mm in length, 3,2*30mm would be ok)
- wood glue (read instructions!)
- needle (curved one special for this type of work) and thread (special sturdy one!)
- sewing machine [if available] (I don’t know if a regular sewing machine is able to get through the upholstery)
- foam and other filling
- a stapler! (I had a pneumatic one, but an electrical or whatever is a must… I don’t thing the manual ones will be able to enter the MDF deep enough).
- knive
- markers

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Pac Man Pouf

DIY: Bunkbed/Loft Organizer

TanYA — Wed, 16 Sep 2009 16:46:16 +0000

Make a quirky bunk bed/loft organizer where you can safely keep stuff like books, reading glasses or mobile phones. To read the full instructions go here and check the list below to see what you will need:

Heavy-weight fabric for backing
Fabric for the pocket (this fabric can be heavy or lighter weight)
2 Buttons

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Bunkbed/Loft Organizer

DIY: Beehive Bookcase

TanYA — Tue, 15 Sep 2009 19:53:12 +0000

Are you a bookworm and always running out of space to keep your favourite possessions? Then maybe you can make your own bookcase and save some hard earned bucks in the process. We really like the Beehive Bookcase, which you can make at home following the directions here.

Materials
Consuamables:
One large sheet of 1/4 inch particle board
Glue
Primer
Paint

Tools:
Table Saw
Clamps
Paint Brushes

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Beehive Bookcase

DIY: Soda Tab Chainmail Laptop Bag

TanYA — Fri, 11 Sep 2009 19:23:51 +0000

You can make this cool Soda Tab Chainmail Laptop Bag at home without burning a hole in your pocket. The dimensions used here perfectly fit a 13″ MacBook, but the proportions can be adjusted for other laptops, or to make other bag sizes. To read the instructions go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Soda Tab Chainmail Laptop Bag

DIY: Make a College Loft Bed

TanYA — Wed, 09 Sep 2009 23:17:15 +0000

Make a College Loft Bed that doest necessary need to be in a dorm room but can also be used in small space. Dimensions given will accommodate an Extra-Long Twin mattress with 1″ extra on every side and here are the things you would need:

Tools:
Miter Saw (power)
Cordless Drill with Screw bit
Corded Drill (opt.) with 3/8″ drill bit

Hardware:
18 3/8″ Carriage Bolts
18 3/8″ Flat Washers
18 3/8″ Lock Washers
18 3/8″ Nuts
Small box of 2-1/2″ Deck Screws (torx opt.)

Lumber:
8 – 2×4x6′
8 – 2×4x8′
3 – 2×6x8′

Read the rest of post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Make a College Loft Bed

DIY: Make A Pretty Couch, Chair or Bed Organizer

TanYA — Wed, 09 Sep 2009 12:08:34 +0000

Make A Pretty Couch, Chair or Bed Organizer for your child or better get them involved in this easy DIY. This DIY teaches how to follow a line on the machine plate, how to follow a creased line with the needle, how to make your own bias tape, turning a good corner, how to use an iron, how to use interfacing and working with various types and thicknesses of fabric. You can read the entire post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Make A Pretty Couch, Chair or Bed Organizer

DIY: LED Desk Lamp

TanYA — Mon, 07 Sep 2009 20:18:01 +0000

Make a cool yet affordable LED Desk Lamp by using supplies from Home Depot and IKEA. The lamp has a flexible and adjustable neck that is made from electrical conduit and stiff wire to keep its shape. You can read the entire instructions here and this is what you would require:

Tools:

* Small Philips screwdriver
* Little Pliers (for bending and cutting wire)
* Big Pliers (for cutting through stiff electrical conduit
* Hole punch (not the kind you find in an office, the kind that looks like a screwdriver but with a very sharp end)
* Note: If you have a drill, you can use that instead of the hole punch. If you have a hacksaw or other metal-cutting tool, get that out as well.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: LED Desk Lamp

DIY: 15 Minutes SMS Door Entry Alarm

TanYA — Mon, 07 Sep 2009 10:11:15 +0000

If you don’t want to splurge on security alarms but still fear intruders then this DIY is perfect for you. The 15 minutes SMS door entry alarm DIY tells you how to build a cheap alarm system that will notify you on your mobile by SMS in case of a break in.

step 1What you’ll need
An old mobile phone set with supply (charger).
Cheap door magnetic alarm (can be replaced by a magnetic switch and a magnet ).
5 volts Relay.
Soldering iron.
wires and thin insulated copper wires.
micro driller.
micro screwdriver set.
clipper.
multimeter.
Scotch tape.

Read the rest of instructions here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: 15 Minutes SMS Door Entry Alarm

DIY: Dress from Pillowcase

TanYA — Wed, 02 Sep 2009 18:47:46 +0000

There is no dearth of pretty pillowcases and one can hence turn them into a cool summer dress too. How? Well just read on.

Step 1 Materials you need:
1 standard sized pillow case with a decorative edge or a great fabric
1 package 1/2 or 1/4 inch coordinating bias tape
a sewing machine
matching thread
scissors
a shirt (for a pattern… will not be cut up!)

For the rest of the post go to Instructables

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Dress from Pillowcase

DIY: How to Fuse Plastic Bags to Make Laptop Case

TanYA — Tue, 01 Sep 2009 19:14:39 +0000

Do your bit when it comes recycling as even a small step goes a long way when it comes to protecting our Planet. Relax, I am not going to go all preachy on you, however would like to share this cool DIY Video which teaches you to how to fuse plastic bags to make a laptop case. It’s pretty neat actually.

Via Instructables

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: How to Fuse Plastic Bags to Make Laptop Case

Make Your Own Guess Who Game

TanYA — Sat, 15 Aug 2009 17:26:48 +0000

Make your own cool version of the Guess Who Game by following all the instructions posted here. Now we can ask questions such as “Has your person ever lived with me?” or “Does your person have a substance abuse problem?” Must say this version is more fun and even a tad insane!

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

Make Your Own Guess Who Game

DIY: Welcome Sign

TanYA — Sat, 15 Aug 2009 17:14:10 +0000

Designer Thomas Voorn found an unique way to welcome guests at his home! In fact we think this can be replicated at home too as all you need are old clothes and loads of imagination.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Welcome Sign

DIY: Laptop Stand

TanYA — Fri, 07 Aug 2009 22:25:58 +0000

Make a simple laptop stand that will keep your laptop cool. It keeps the computer off the surface, gives excellent air circulation and elevates it to a comfortable typing angle and the best part? You don’t need to spend more than 10$!

Here are the materials you’ll need:

1 Metal Mesh Document Holder (I bought mine at Staples for $6, it comes in black or sliver)
1 Roll of Anti-slip shelf liner (bought it at the dollar store)
1 Small block of rubber – This corner piece came in the packaging of my air-conditioner to protect the corners. You can probably find something similar at the hardware or dollar store such as a rubber sandpaper block; just cut the sandpaper sides off.
Glue gun
Double sided tape
Utility blade
Ruler

Go here for the rest of the post.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Laptop Stand

DIY: Cool Cardboard Chair

TanYA — Thu, 06 Aug 2009 20:18:07 +0000

Make a cool cardboard chair that is ideal for college students or those who want a cheap seating solution. The chair is based on Frank Gehry’s Wiggle Chair,” popularized in the 1970’s that took advantage of the versatility of cardboard as a medium.

Step 1 Materials and Design!
YOU NEED THIS
- Cardboard – We got all the cardboard we needed at the township’s cardboard recycling dumpster. Look for large pieces, but be careful of double ply and triple ply as they are hard to work with (with our system). FREE!

- Plywood -Two sheets large enough for the chair’s profile. Look for the hardest wood you can find. It needs to stand up against a lot of wear and force! About $40.

- Router -Yes we need powertools! Price varies.

- Bandsaw blades (2 or 3) -Thin blades, look for flat teeth, and about 1in tall. About 25 each.

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Cool Cardboard Chair

DIY: Rubber Hose Chair

TanYA — Wed, 05 Aug 2009 00:04:20 +0000

Make a Rubber Hose Chair and then enjoy it by lounging around the whole day. To make the chair comfortable ensure that there is narrow enough spacing and a tight-enough weave so that weight is evenly distributed. The overall form is quite reclined, with an interior width of about 22″. Assuming the hose is recycled (garden hose would work as well, though it typically is made from thinner rubber), the only other materials are one 2′x 2′ piece of 3/4″ plywood and four 2′ x 1/2″ dia. threaded rods with nuts and washers.

Read the instructions here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Rubber Hose Chair

DIY: Pillow Speaker

TanYA — Fri, 31 Jul 2009 16:03:46 +0000

Nothing like falling asleep listening to your favourite tunes. For me it’s always a cathartic experience and hence I loved the homemade Pillow Speaker. Like the commercially available ‘Sound asleep Pillow’, you can plug in any audio device, Ipod, computer, etc and listen to music or watch a film without getting tangled up in earphones.

You will need:

- Pillow & pillow case
- Old headphones, earphones are not ideal but will do
- Female 3.5mm jack connector
- Wire
- Soldering iron
- Solder
- Heat-shrink tubing
- Scissors
- Needle and thread
- 2 part epoxy or hot glue

You may need:

- Fabrics paints
- Brush
- Drill

For the rest of the post go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Pillow Speaker

DIY: Record Lamp

TanYA — Thu, 30 Jul 2009 19:03:56 +0000

Make an uber cool lamp from old records and be the talk of your friends circle. The lamp not only looks groovy but also has a very Retro vibe going it for. To do this project you’ll need a number of things…

50-75 translucent records plus a few that don’t need to be translucent
A light bulb, fixture, switch and cord
a base
threaded rod, washers, nuts and acorn nuts

For the rest of the post go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Record Lamp

DIY: Harry Potter Wand

TanYA — Wed, 22 Jul 2009 23:15:18 +0000

It’s hard not to be bitten by the Harry Potter bug now that the latest installment of the movie is here. So we thought you can show your affinity to your favourite wizard by building your own Harry Potter wand.

Step 1 Get a cheap UV marker and key ring LED set
you can get these off the web, or from Amazon. I have searched for them and there are some links on the Magical Wands page of dadcando for the cheapest I could find, but most big office stationers or art shops should stock them.

Step 2 take apart LED keyring
take the LED key ring light apart. take care to see which of the LEDs legs is touching the positive battery terminal, in this case it was the short one. If the leg is bent like this one is, it might need straightening out to fit inside a drinking straw (you’ll see why on a few steps).

The batteries which come with most keyring lights are these CR2016 (that’s 20mm diameter and 1.6mm thickness BTW). I felt that the diameter of 20mm was too much for a wand handle so I looked around for a narrower 6-volt battery. The best I found was the 6V camera battery 4LR44. As all our joins to the battery are going to be by taping the wires on the less batteries we have to join together the better, so a single battery for the whole 6v is what you want.

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Harry Potter Wand

DIY: Give a Makeover to Your Laptop

TanYA — Wed, 22 Jul 2009 17:50:36 +0000

Tired of how your laptop looks and want to give it a makeover without breaking the bank? Then you will love this DIY project as the end result is a mighty pretty laptop!

step 1 Design the template
Bold designs work best. Try to keep all features larger than 0.150 inches.

This one is designed such that you can cut it from one piece of material and then snaps in the interior pieces to do different layers. Since you never have to remove the first layer, the subsequent layers are already aligned.

If you are going to laser cut the template, make sure your design is in a vector format. Programs such as Adobe Streamline can turn bitmaps into vectors.

For the rest of the post go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Give a Makeover to Your Laptop

DIY: Monster Speakers

TanYA — Mon, 20 Jul 2009 22:37:32 +0000

How cute are the Monster Speakers? The best part is no doubt that you can make something like this t home easily. First we need to make a pattern! Get some newspaper and fold and form it over your speakers. Tape helps a lot in this process. And scissors. You will want scissors.

Create seams and darts wherever the paper meets.

Mark where the ‘eye’ and ‘mouth’ openings will be.

* If you are using fur, consider the “nap” – which way the fur is directed. You don’t want one side with the fur going up and one with it going down.

Also make patterns for any add-ons, like wings, feet, etc. You are limited only by your imagination! (more on that in step 7)

Open your pattern flat and straighten any wonky edges with a ruler.

Measure each side to make sure all corresponding seams are the same length. You’d be surprised at how often they aren’t.

Read the rest of the entry here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Monster Speakers

BED DIY – How to Make a Bedside In-Wall Shelf!

Max — Mon, 20 Jul 2009 17:48:34 +0000

For those of you looking to save space while rejuvenating your bedside tables, you might want to look into this DIY on how to make a bedside in-wall shelf. (via diy blog)

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

BED DIY – How to Make a Bedside In-Wall Shelf!

DIY: Twister Blanket

TanYA — Fri, 17 Jul 2009 19:16:25 +0000

We all have grown up playing Twister and who didn’t love this crazy game? Now one can even travel with it as you can make your very own Twister Blanket!

Here are the things you need:

* Two yards of white fleece ($8.88)
* Two yards of some other color material, it doesn’t necessarily have to be fleece, and it’s pretty much optional. (I used grey fleece, which was also $8.88)
* Felt. Or you could use some other type of material I guess. You’ll need six circles cut out of each green, red, blue, and yellow.
* Scissors
* A tape measure or something that will help you get all those darn dots lined up.
* A sewing machine and thread. Or I suppose you could hand sew it, but I’m not sure why you would want to. That would be a lot of sewing. Whatever floats your boat I guess.
* Chalk or something to draw on the felt with. I used a pen, but that didn’t work so well.
* Something circular that is the size you want your dots to be. Mine were 6 1/2 inches across.

Read

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Twister Blanket

Recycle Denim

TanYA — Wed, 15 Jul 2009 22:53:02 +0000

Don’t throw away those old jeans as you can recycle denim and make a whole variety of stuff ranging from floor mats to waistbands. This comfy floor mat is made from recycled waistbands, hem cuffs, and inseams from old jeans. These are often the wasted scraps left after other projects with recycled denim.

For the full post go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

Recycle Denim

DIY: LED Frisbee

TanYA — Tue, 14 Jul 2009 21:47:05 +0000

Make a cool LED Frisbee at home and watch the kids go crazy. 2×3mm blue LEDs and 1×5mm green LED have been used and all the LED’S connect in the middle. They also connect to a small switch, so the batteries don’t die. 3 button cells around the connector thing to run the LED’s.

Read.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: LED Frisbee

DIY: Outdoor Activity Table

TanYA — Mon, 13 Jul 2009 18:30:11 +0000

Build an outdoor activity table for your children using scrap materials. The project also isnt very time consuming as it takes approximately an hour or two.

Materials
1. Restless child looking for something to do
2. 4 (4 x 4) blocks
3. 1 Sheet of plywood
4. Deck screws
5. Drill
6. Counter sink + deck screw bit
7. Sander

Optional

Speed Square (This made making the corner lines easy)

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Outdoor Activity Table

DIY: Stained Glass

TanYA — Sat, 11 Jul 2009 16:09:13 +0000

Get in touch with the creative genius inside you and try your hand at making stained glass objects.

This is what you will need:
-A pattern (find one on the internet, alot of times i can’t find one so i use simple children’s coloring pages for a pattern, or you can just draw your own)
-Safety glasses (glass goes everywhere)
-Gloves (optional- i dont use gloves but i also cut my hands when doing this)
-Glass (you can even use mirror if you like)
-Copper Tape (i use 1/4 in thickness)
-Solder (50% Lead, 50% Tin)
-Flux

Tools:
-Glass Grinder (you can do without one but it is easier and makes edges cleaner)
-grozing pliers (these or ones specially made for glass)
- Glass Cutter
- Flux Brush
- Sharpie

Read the rest of the instructions here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Stained Glass

DIY: Fridge Magnets

TanYA — Fri, 10 Jul 2009 01:39:21 +0000

If you like experimenting and love using waste materials to make a décor statement then you will like this DIY which shows how you can turn your extra bottle caps into simple yet cool fridge magnets.
Here’s the bare bones materials list:

- bottle caps
- sandpaper (I used 220 grit… the grit isn’t critical)
- hot glue gun
- hot glue sticks
- button magnets (1/2″)
- 1/4″ hex nuts

For the rest of the post go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Fridge Magnets

DIY: Make a Rainbow Canopy

TanYA — Thu, 09 Jul 2009 22:34:44 +0000

Make a Rainbow Canopy for your kid’s bedroom and watch theM have the time of their life. Requirements: It needed to be sturdy, flexible, removable, washable, and inexpensive. This is all of those, plus the requested curtains.

It has become a stage, a secret hiding place, a teaching tool (colors!), a toy in and of itself. Oh, and it’s also a bed.

NOTICE: Do not use for a crib-bed that is still in use as a crib. If you want to make this for a non-crib toddler bed, you will have to create your own pattern and customize your frame.

For the rest of the post go here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Make a Rainbow Canopy

DIY: Oriental Paver/Stepping Stones

TanYA — Tue, 07 Jul 2009 15:07:20 +0000

Make beautiful Oriental Paver/Stepping Stones for the garden and who knows maybe you will also get the benefits of feng shui.

step 1Materials Needed

1. Form(s) for the stepping stone

2. Cement, mortar, sand, water, usual concrete items.

3. Buckets

4. Trowels, spreaders, etc.

5. Sponges

6. Cans or measuring cups to measure the various ingredients.

7. Styrofoam or EPS foam (To make letters for the name, message).

9. Hotwire machine…Mighty Goliath! (See my instructable: making the mighty goliath).

10. I Use regular white glue or the tacky kind….either works fine.

“I use stencils found in any craft store. It’s possible to go online, search and find asian flavored lettering as well! For this instructable, I have chosen “Love” as the project, with others shown to supply details.”

Read the rest of the post here.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Oriental Paver/Stepping Stones

DIY: Solar USB Charger

TanYA — Wed, 01 Jul 2009 21:12:09 +0000

Make your own Solar USB charger and show you care about Mother Nature. The DIY USB Charger puts about 6v and is perfect for charging anything that uses USB. This is also perfect for someone new to soldering!

You need the following:
1x USB extension a/a cable
1x Any Diode (RadioShack #: 276-563)
1x 6v Solar panel (RadioShack #: 277-1205 )
Soldering iron(RadioShack #: 64-2051)
Solder
1x Project box (Radioshack #: 270-1803) I would maybe chose a smaller on, I had a bigger one laying around.
Electrical Tape
Glue Gun or tape to hold the peices in place.
Drill

Go here for the rest of the post.

Brought to you by: BED Online Magazine - The Bed Blog - We are crazy about beds.

DIY: Solar USB Charger

BED Online Magazine - The Bed Blog - We are crazy about beds. » diy

DIY: Christmas Ornaments

Related posts

DIY: Scrap Table

Related posts

DIY: Bean Bag Warmers

Related posts

DIY: Rustic Outdoor Table

Related posts

DIY: Floating Candles

Related posts

Periodic Picnic Table

Related posts

Kitchen DIY – How to Add a Colorful Backsplash to Your Kitchen Counter!

Related posts

Chair Design DIY – How to Make a K’nex Chair!

Related posts

DIY: USB Flash Drive Rubiks Cube

Related posts

BED Accessory DIY – How to Make Super Mario Bros. Themed Baskets!

Related posts

DIY: Pumpcans (Pop Can Jack-O-Lanterns)

Related posts

DIY: iPhone Alarm Stand

Related posts

DIY: Halloween Lamps

Related posts

DIY: Tooth Fairy Pillow

Related posts

DIY: Super Cool Chair Tent

Related posts

DIY: Build a Polished Concrete Desk

Related posts

KipKay Alarm Clock

Related posts

Laptop Stand for Bed

Related posts

Tea Light Lantern Fluorescent Lamp

Related posts

DIY: Work Desk

Related posts

DIY: Pac Man Pouf

Related posts

DIY: Bunkbed/Loft Organizer

Related posts

DIY: Beehive Bookcase

Related posts

DIY: Soda Tab Chainmail Laptop Bag

Related posts

DIY: Make a College Loft Bed

Related posts

DIY: Make A Pretty Couch, Chair or Bed Organizer

Related posts

DIY: LED Desk Lamp

Related posts

DIY: 15 Minutes SMS Door Entry Alarm

Related posts

DIY: Dress from Pillowcase

Related posts

DIY: How to Fuse Plastic Bags to Make Laptop Case

Related posts

Make Your Own Guess Who Game

Related posts

DIY: Welcome Sign

Related posts

DIY: Laptop Stand

Related posts

DIY: Cool Cardboard Chair

Related posts

DIY: Rubber Hose Chair

Related posts

DIY: Pillow Speaker

Related posts

DIY: Record Lamp

Related posts

DIY: Harry Potter Wand

Related posts

DIY: Give a Makeover to Your Laptop

Related posts

DIY: Monster Speakers